To order, you can add products to your Wishlist, then email it to a dealer:
Carb to manifold gasket 6-pack
Six gaskets in a handy pack. Always replace the gasket if you remove the carburetor from the intake.
Full gasket kit
Fits Stromberg 97, 81, 48, and 40. Three main gaskets (high tech cellulose/nitrile mix), plus a new felt gasket for the accelerator pump, and fibre ring gaskets for the power valve, inlet valve and drain plugs (5 - 2 spare).
Bulk gasket kit
Full gasket kits (as 9447K above) but five whole sets.
Accelerator pump rod - 48/40
All stainless steel with the correct swaged ends. Check you have the right size. This one is shorter because the 48 and 40 models have a different throttle shaft end bracket – without the S and W options.
Accelerator pump rod - 97/81
All stainless steel with the correct swaged ends. Check you have the right size. This one is longer because the later 97 and 81 models have the improved throttle shaft end bracket with Summer and Winter choices.
Emulsion tubes - pair
If your emulsion tubes are blocked or crushed, your engine is never going to run properly. A super-precision piece to fit 97, 48, 81, 40 and LZ carburetors. No Stromberg rebuild is complete without these beauties.
Idle mixture screw kit
Included in our Premium Service Kits (9590K) but also separately here. Two new screws with stainless steel springs.
Idle jets - pair
Not often a problem, but we've got them if you need them. They must seal securely in the casting on that angled seat just below the cross-hole at the top end.
Bowl plug gaskets x 10
If your Stromberg is leaking from underneath, these could be the answer.
S-jet inlet valve
The Genuine Stromberg twin-ball S-jet is the 'next generation' needle and seat. It's designed to eject dirt particles and improve high speed running and, unlike many a so-called viton-tipped needle valve, it won't stick or melt in today's corrosive new gas formulas. Comes with a new fibre washer. Fits Stromberg 97, 48, 81 and 40.
Accelerator pump check valve
Hides under the center bowl plug and allows the accelerator pump to suck gas in, but not back out into the float bowl. Comes in the Premium Service kit (9590K).
Throttle/choke plate screws x 10
If you're removing the choke or throttle plates, new screws are a must. The hollow ends allow them to be staked on the back to prevent shaking loose.
Premium service kit - 81
The best service kit available for your Genuine Stromberg 81. Comes with a full gasket kit, Stromberg S-jet inlet valve, accelerator pump check valve, two idle mixture screws and springs, full 81-size accelerator pump kit (with correct leather seal and springs), and a detailed Installation Guide.
Premium service kit - 97/48/40
The best service kit available for your Stromberg 97, 48 or 40 carburetor. Comes with a full gasket kit, Stromberg S-jet inlet valve, accelerator pump check valve, two idle mixture screws and springs, full accelerator pump kit with new springs, and a detailed Installation Guide.
Accelerator pump kit - 81
Talk about original. Our Stromberg 81 accelerator pump has the correct 10-finger brass spring washer and small bore leather seal. The kit includes new springs, retainer, washers, felt gasket and cotter pin.
Accelerator pump kit - 97/48/40
Full accelerator pump kit for Stromberg 97, 48 and 40 carburetors. Includes new springs, retainer, washers, felt gasket and cotter pin.
Accelerator pump - 81
What a beauty. With with correct Stromberg 81 10-finger brass spring washer and genuine leather seal. If you need new springs, washers, retainer and more, choose 9631K-81.
Accelerator pump - 97/48/40
Accelerator pump for Stromberg 97, 48 and 40 with correct length and leather seal. If you need new springs, washers, retainer and more, choose 9631K.